Saturday, November 16, 2013

#Fukushima I Nuke Plant: TEPCO Admits Total 80 Spent Fuel Assemblies Had Damages Before the Nuclear Accident, 70 of Them in Reactor 1 Spent Fuel Pool


Move over, three fuel assemblies with damaged/deformed fuel rods inside in the Reactor 4 Spent Fuel Pool! You're nothing.

According to Kahoku Shinpo, a Fukushima local paper, TEPCO admitted on November 15, 2013 that there are 70 fuel assemblies with damaged fuel rods in the Reactor 1 Spent Fuel Pool, located on the operating floor (top floor) of the reactor building whose air radiation levels are measured in millisievert/hour and sievert/hour (first floor).

There are also three such fuel assemblies in the Reactor 2 SFP, and four of them in the Reactor 3 SFP.

Total 80 spent fuel assemblies in the SFPs in Reactors 1 - 4 are damaged.

The damages had been there long before the March 11, 2011 accident, and TEPCO claims it properly notified the national government as they discovered the damages. But the company has come clean in public only now.

Kahoku Shinpo article below suggests that the oldest of such damaged fuels may have been there for 40 years in the Reactor 1 Spent Fuel Pool. (Reactor 1 started generating electricity in 1971.)

Reactor 1 at Fukushima I Nuke Plant is TEPCO's oldest nuclear reactor; it was entirely the project by General Electric of the US, a turnkey.

From Kahoku Shinpo (11/16/2013):

福島第1原発1号機 燃料震災前破損70体 全体の4分の1

Fukushima I Nuke Plant Reactor 1 has 70 fuel assemblies damaged before the March 11, 2011 disaster, a quarter of the total spent fuel assemblies [in the Spent Fuel Pool of Reactor 1]

福島第1原発1号機の使用済み燃料プール内にある燃料棒70体が東日本大震災前から損傷していたことが15日、分かった。

It was revealed on November 15 that 70 fuel assemblies in the Reactor 1 Spent Fuel Pool at Fukushima I Nuclear Power Plant had had damages before the March 11, 2011 earthquake/tsunami.

プール内に保管されている使用済み燃料292体の4分の1に相当する。損傷した燃料棒を取り出す技術は確立しておらず、2017年にも始まる1号機の燃料取り出し計画や廃炉作業への影響が懸念される。

The damaged assemblies are about one-quarter of the 292 spent fuel assemblies stored in the pool. Technologies to remove damaged fuel haven't been established, and there are worries that [the revelation] may negatively affect the plan to remove the fuels from Reactor 1 [SFP] starting 2017 and the decommissioning work in general.

東京電力は、15日まで事実関係を公表してこなかった。同社は「国への報告は随時してきた」と説明している。

TEPCO hadn't disclosed all the facts until November 15. The company says it had reported to the national government as required.

東電によると70体の燃料棒は、小さな穴が空いて放射性物質が漏れ出すなどトラブルが相次いだため、原子炉から取り出してプール内に別に保管していたという。

According to TEPCO, these 70 fuel assemblies had series of problems including leakage of radioactive materials from small [pinhole-size] holes [on fuel rods]. So the company removed them from the reactor and stored in a separate location inside the Spent Fuel Pool.

18日に燃料取り出しが始まる4号機プール内にも損傷した燃料棒が3体あり、東電は通常の取り出しが困難なため、対応を後回しにしている。

There are three damaged fuel assemblies inside the Reactor 4 Spent Fuel Pool, where the removal of the fuel assemblies will start on November 18. TEPCO has postponed the removal of the damaged assemblies as it is difficult to remove them in a normal manner.

損傷した燃料棒は1、4号機プールのほかにも2号機プールに3体、3号機プールに4体の計80体ある。東電は専用の輸送容器を新たに製造するなど対応策を検討する。

Other than in the Spent Fuel Pools of Reactor 1 and Reactor 4, the Reactor 2 Spent Fuel Pool has three damaged fuel assemblies, and the Reactor 3 Spent Fuel Pool has four, making the total of damaged fuel assemblies 80. TEPCO will consider the measures such as building a dedicated container for transfer for these damaged fuels.

損傷燃料が1号機に集中している理由について、東電は「1号機は当社で最も古い原発で、燃料棒の製造時、品質管理に問題があり粗悪品が多かったと聞いている。2号機以降は燃料棒の改良が進み、品質は改善した」と説明した。

As to the reason why Reactor 1 has the largest number of damaged fuels, TEPCO says, "Reactor 1 [at Fukushima I Nuke Plant] is the oldest nuclear reactor of our company, and we hear that there were quality control issues when the fuel rods were manufactured and that there were many fuel rods with inferior quality. From Reactor 2 onward, much improvement was done on the fuel rods, and quality improved."

1号機は東電初の原発で、1971年3月に商業運転を開始した。

Reactor 1 at Fukushima I Nuke Plant is the first nuclear reactor for TEPCO, and it started the commercial operation in March 1971.


No major national newspaper has covered this story so far.

Friday, November 15, 2013

#Fukushima I Nuke Plant Reactor 1: Surface Boat in the Flooded Torus Room Finds Two Leaks from the Dry Well (CV)


The small boat that can, fitted with video camera and dosimeter, boldly going where no humans can ever go (ambient air dose of 1.8 SIEVERT/hour max).

The boat was lowered from a hole (510mm in diameter) drilled on the floor of the 1st floor of Reactor 1 into the torus room which is flooded with highly contaminated water leaking from the dry well.

The surface boat, by Hitachi Nuclear Energy (from TEPCO's Photos and Videos Library 11/13/2013):


The route of the surface boat (red for November 13 expedition, blue for November 14):


Leak 1: the upper part of the S/C facing side of the vent pipe at the location [4] (S/C = Suppression Chamber):


Leak 2: The sand cushion drain pipe at the location [1]:


The video taken by the boat:



(Oh my goodness, what are they capturing in the lower left screen? It looks like some organic materials growing on the metal surface...)

The boat looks to be tethered, meaning human workers from Hitachi Nuclear Energy were operating it from the 1st floor of the Reactor 1 building which has rather high air dose levels (unlike Reactor 4, the levels in Reactor 1 is in millisievert/hour, with several locations in sievert/hour). There is no information as to the radiation exposure for the workers who operated the boat.

Now, we need a little submarine that could to dive under the water in the torus room and check the damage on the Suppression Chamber and the surrounding walls.

And a swarm of self-organizing, self-propelled small flying robots for the upper floor surveys, and an army of soldier ant robots to eat away the irradiated concrete debris on the operating floors and inside the Spent Fuel Pools of Reactor 3 and Reactor 4.

Fuel Assembly Removal to Start on November 18, 2013 From #Fukushima I Nuke Plant Reactor 4 SFP


According to NHK (11/15/2013), TEPCO will start removing the fuel assemblies from the Spent Fuel Pool of Reactor 4 at Fukushima I Nuclear Power Plant on Monday, November 18.

TEPCO will start with unused (therefore not irradiated) new fuel assemblies (there are 202 of them in the pool). 22 new fuel assemblies will be the first to be moved UNDER WATER into the container (called "cask") in the cask pit, using the fuel handling machine. Then the sealed cask will be lifted out of the pool by the gantry crane onto the truck waiting on the ground, which will transport the cask to the Common Pool about 100 meters away. TEPCO has two casks to be used for transport.

After removing 22 new fuel assemblies, then TEPCO will start removing the spent fuel assemblies. The removal is scheduled to continue until the end of next year, "ahead of schedule" as has been loudly demanded by the LDP politicians.

The fuel handling machine in the foreground, over the Spent Fuel Pool, and the gantry crane in the back, as workers conduct a dry-run on November 14 using mock fuel assemblies on the Reactor 4 operation floor (from TEPCO, 11/15/2013; click to enlarge; follow the link for more photos):


Workers who tweet from Fukushima I Nuke Plant say the people who will be operating the fuel handling machine and the gantry crane are the workers with long experience and expertise in fuel handling, from TEPCO's primary contractors. Not "yakuza and rank amateurs".

==========================

To disabuse some people, including scholars and experts (albeit in different fields, not related to nuclear energy or nuclear power plant technologies, or who simply have not followed the Fukushima nuclear accident much other than catching some soundbites), the following is NOT, I mean NOT, how the fuel assemblies will be removed. (I couldn't believe it at first, but there were many in Japan for example who thought the removal would be done exactly like this. Maybe they still do...)

First, we use a crane like this one (whose jib mast collapses after 1:35 into the video)...



And we will take out individual fuel "rods" (and not fuel assemblies) one by one, like this one being taken out of the fuel assembly (casing has been already removed)(from TEPCO, 8/28/2012):


And using the crane in the first photo, and pull the fuel "rods" out of the pool into open air, irradiating the workers regardless of whether the "rods" are new or used, like this (except in this case it was an unused new fuel ASSEMBLY with the casing, not an individual rod)...


Then the "rods" will then be placed in a container, and the container will be lowered to the ground...

In the process, a mishap may occur, and the fuel rods may be scattered on the ground, then they go critical.

And on and on till the end of either the northern hemisphere or the entire planet.

This dire scenario is best summarized by a Yale University sociology professor (emeritus), who says the Reactor 4 SFP is in danger of collapsing (from Huffington Post 9/20/2013; emphasis is mine):

Much more serious is the danger that the spent fuel rod pool at the top of the nuclear plant number four will collapse in a storm or an earthquake, or in a failed attempt to carefully remove each of the 1,535 rods and safely transport them to the common storage pool 50 meters away. Conditions in the unit 4 pool, 100 feet from the ground, are perilous, and if any two of the rods touch it could cause a nuclear reaction that would be uncontrollable. The radiation emitted from all these rods, if they are not continually cool and kept separate, would require the evacuation of surrounding areas including Tokyo. Because of the radiation at the site the 6,375 rods in the common storage pool could not be continuously cooled; they would fission and all of humanity will be threatened, for thousands of years.


Just like many North American experts, the professor simply declares conditions in the Reactor 4 SFP are "perilous". The common Pool is 100 meters away, not 50 meters. It's not "rods" but "assemblies". No idea what he's talking about when he says "two of the rods touch", but I have seen this phrase in other places from other experts. It must be part of the standard things to say if you are to comment on the fuel "rods" from the SFP at Fukushima I Nuke Plant. That Tokyo is part of "surrounding areas" of the plant would be news to most Japanese.

Compared to other reactors that suffered the core melt, the air radiation levels in Reactor 4 have been low enough (measured in microsievert/hour instead of millisievert/hour in other reactors) to allow human workers to work inside the reactor building and on the top floor for the past two and a half years.

For a fond memory, this was the operating floor of Reactor 4:

March 16, 2011:


April 10, 2011:


June 30, 2011:


Tuesday, November 12, 2013

#Fukushima I Nuke Plant Reactor 4 SFP: Three Fuel Assemblies Deformed or Damaged, Says TEPCO


It must be from the explosion! Or from something TEPCO has done since the accident, whatever it is!

No.

If TEPCO is to be believed, TEPCO has been hiding the damages for at least 10 years; the oldest damage was from 25 years ago.

According to Yomiuri Shinbun (11/12/2013), that's not clear, and you would be excused if you thought the damages were recent (after March 11, 2011).

From Yomiuri Shinbun (11/12/2013):

東京電力は12日、今月中に取り出し作業が始まる福島第一原子力発電所4号機の使用済み核燃料プールの1533本の燃料に、変形などのために取り出しが困難なものが3本あることを明らかにした。

On November 12, TEPCO disclosed that there were three fuel assemblies out of 1533 fuel assemblies in the Spent Fuel Pool of Reactor 4 at Fukushima I Nuclear Power Plant that were deformed and would be difficult to remove. The removal of fuel assemblies from the Reactor 4 SFP will start this month.

問題の3本には、過去の作業で生じたわずかな変形や損傷がある。放射性物質の漏れは確認されていない。東電は、ほかの燃料の移送を優先させ、3本の取り出しと移送の方法は今後検討する。原子力規制委員会は、取り出し作業の安全性を認めており、作業は月内に予定通り開始される。

The three fuel assemblies has slight deformation or damage caused by the past work [in the SFP]. No leak of radioactive materials has been observed. TEPCO will transport other fuel assemblies first, while they figure out how to remove and transport these three fuel assemblies. Nuclear Regulation Authority has already approved the fuel removal, and the work will start within this month as scheduled.


So, are these fuel assemblies new? used? How long ago was the "past work"?

I found the answer in Fukushima Minyu, one of the local newspapers in Fukushima Prefecture. It was long before the start of the March 11, 2011 nuclear accident, with the oldest "past work" 25 years ago...

From Fukushima Minyu (11/13/2013; part):

東電によると、損傷した燃料の1体は「く」の字に折れ曲がっている状態。25年ほど前に燃料を取り扱う際に失敗し曲がった。ほかの2体は10年ほど前に破損が分かり、異物などの混入で外側に小さな穴が開いた状態という。

According to TEPCO, one of the damaged fuel assemblies is bent at a 90-degree angle [literal meaning: bent in the shape of a Japanese character "く"; actual angle could be less]. It was bent 25 years ago when a mistake occurred in handling the fuel. The other two were found to be damaged 10 years ago; there are small holes on the outside from foreign objects.

燃料損傷について当時公表したかどうかは東電が調査中。

TEPCO is investigating whether the damages to the fuel assemblies were made public when they were discovered.


According to Fukushima Minyu, the occasion was a visit by the delegation of the Fukushima Prefectural Council for Decommission Safety Monitoring. The council members include officials from the Fukushima prefectural government, municipalities around Fukushima I Nuclear Power Plant, and experts.

How do you bend a fuel assembly at a 90-degree angle, handling it in the spent fuel pool?

And how could Yomiuri call a fuel assembly bent at a 90-degree angle "slight deformation"? Slight?

--------------

For your information, there are 1533 fuel assemblies (each of which contains 50 to 60 fuel rods in channels inside the casing) in the Spent Fuel Pool of Reactor 4 at Fukushima I Nuclear Power Plant.

There used to be 1535 fuel assemblies there, but two new fuel assemblies were taken out from the Reactor 4 SFP last year for examination.

Of 1533 fuel assemblies currently in the Reactor 4 SFP, 202 of them are never-used, brand-new fuel assemblies. The rest, 1331 are used fuel assemblies. Of 1331, 783 are spent fuel assemblies that have been stored in the SFP at least for several years; 548 are the fuel assemblies that had been used in the Reactor Pressure Vessel until Reactor 4 went into extended maintenance to replace the core shroud. These 548 "hot" fuel assemblies were taken out of the Reactor Pressure Vessel and placed temporarily in the Spent Fuel Pool.

Monday, November 11, 2013

(OT) Mazda SUV with Automatic Braking Crashes in Japan Drive Test


Oops.

A prospective buyer at a dealership in Saitama Prefecture sustained slight neck injuries, while the dealership employee on the passenger's seat broke his arm.

From Bloomberg News (11/11/2013):

A Mazda Motor Corp. (7261) sport-utility vehicle equipped with an automatic-braking system crashed in Japan on Nov. 10 during a dealership test drive, injuring the driver and front-seat passenger, according to the police.

The Mazda CX-5 was being driven by a prospective buyer on the dealership’s parking lot when it crashed through a urethane barrier set up to demonstrate the SUV’s automatic braking feature, according to the Saitama Prefectural Police, which is investigating the accident. The customer suffered a neck injury while the dealership employee sitting in the front passenger seat fractured his arm, the police said.

A Mazda Motor Corp. (7261) sport-utility vehicle equipped with an automatic-braking system crashed in Japan on Nov. 10 during a dealership test drive, injuring the driver and front-seat passenger, according to the police.

The Mazda CX-5 was being driven by a prospective buyer on the dealership’s parking lot when it crashed through a urethane barrier set up to demonstrate the SUV’s automatic braking feature, according to the Saitama Prefectural Police, which is investigating the accident. The customer suffered a neck injury while the dealership employee sitting in the front passenger seat fractured his arm, the police said.

(Full article at the link)


More crash details from Yomiuri:

車は約7メートル離れた場所から発進したが、マットにぶつかった後、約6・6メートル先のフェンスに衝突した

The car started from about 7 meters away [from the urethane mat]. After hitting the urethane mat, the car collided with the fence about 6.6 meters away.


Needless to say, the car was supposed to detect the mat and stop.

Automatic braking and automatic (self) driving are touted as the next huge things for the auto industry.

(I'd rather drive a stick-shift pickup truck from 1980s and will make sure I don't go anywhere near the newer-looking Japanese automobiles...)

Sunday, November 10, 2013

(OT) US Fed's Purchase of MBS (Part of QE) after the "Lehman Shock" Were For Foreign Governments, Foreign Central Banks, Foreign Investors, Says Nikkei


I just saw this article at Zero Hedge "The Biggest Difference Between QE3 And QE2", which wonders aloud at the end:

But when more than half of the proceeds of QE to date... have ended up at foreign banks, perhaps at least a theatrical congressional hearing is in order?


That has brought to mind an article that I read yesterday in Japan's Nikkei Shinbun, which said part of the quantitative easing by the US Federal Reserve after the so-called "Lehman Shock" in September 2008 was not so much about helping the US domestic banks or the US housing market but about responding to the demand for the US action from foreign governments for their financial institutions, particularly from China and Japan, two largest foreign holders of the US treasuries AND mortgage-backed securities issued by Fannie Mae and Freddie Mac.

In the US, the purchase of mortgage-backed securities (MBS) issued by Fannie and Freddie by Federal Reserve has been explained as measures to support the housing market. It's that way even today.

From Nikkei Shinbun (11/10/2013; part):

リーマン・ショックから2カ月。米連邦準備理事会(FRB)は緊急危機対応策として、米住宅公社が発行・保証する長期証券の買い入れに踏み切った。今なお続く異例の金融緩和の幕開け。FRB議長、ベン・バーナンキの背中を押したのは、日本や中国など各国からの悲鳴と圧力だった。

Two months after the "Lehman Shock", the US Federal Reserve decided to purchase long-term bonds issued and guaranteed by the US government corporations [Fannie Mae adn Freddie Mac], as emergency response measures. It was the beginning of the extraordinary monetary easing that still continues today. What forced Chairman Ben Bernanke's hand was the cry for help and the pressure from foreign governments, including Japan and China.

2008年11月24日夜、米ワシントンのFRB本部。「あす発表する。追加対策のパッケージを大至急、仕上げてくれ。一枚紙の要旨で、すぐに」。事務方に指示したバーナンキの声はわずかに震えていた。

November 24, 2008 at night, Federal Reserve Board in Washington DC. "I will announce it tomorrow. Prepare the package for additional measures as soon as possible. One-page summary, and quick." Bernanke instructed the staff with a slight quiver in his voice.

 翌25日早朝、FRBは緊急理事会を招集。米連邦住宅抵当公社(ファニーメイ)などが発行・保証する長期証券の買い入れを柱とする危機対応策を決めた。

Early next morning on November 25, Federal Reserve Board called an emergency meeting and decided on the emergency response measures that centered on the purchase of long-term bonds issued and guaranteed by Fannie Mae [and Freddie Mac].

 米東部時間午前8時15分。FRBが発表した声明は紙一枚にわずか13行。だがFRBが買い入れると表明した長期証券の総額は6000億ドル(約59兆円)にも上った。中央銀行であるFRBが市場から直接、証券を買い入れる異例の措置の始まりだった。

8:15AM US Eastern time. The announcement by FRB was typed on one page, in 13 lines. The total amount of purchase by Federal Reserve would, however, be 600 billion dollars. It was the beginning of an extraordinary measures whereby Federal Reserve, central bank of the US, would buy bonds directly from the market.

「とにかく市場の安心感を最優先に考えた。金額の根拠は乏しかった」。当時の議長側近は振り返る。

"Our first priority was to assure the market. There was little basis for the amount," says an aide to the chairman at that time.

FRBが真っ先に住宅公社が発行・保証する長期証券の買い入れに動いたのはなぜか。「危機の震源である住宅市場の下支え」が表向きの理由。だが裏にはリーマン・ショック前夜、米国として示した「国際公約」があった。

Why did Federal Reserve choose to buy the long-term bonds issued by Fannie and Freddie? The official (ostensible) reason was "to support the housing market which was the cause of the financial crisis". However, there was an "international pledge" [as the real reason] that the US government had made right before the "Lehman Shock".

 08年9月7日夜。ファニーメイなど住宅公社2社の公的管理を発表した米財務長官、ヘンリー・ポールソンは電話に飛びついて説明した。「これで米国政府が完全に後ろ盾になった」。相手は中国の当局者。ポールソンは主要7カ国(G7)の当局者との緊急電話会議も開催。米政府として初めて、住宅公社などが発行する米政府機関債の保証を対外的に公約した。

On the night of September 7, 2008. Treasury Secretary Henry Paulson had just announced the effective takeover of Fannie and Freddie, and he was now on the phone. "The US government will now fully back these companies." The Treasury Secretary was talking to the Chinese counterpart. Paulson also conducted a teleconference of G7 finance ministers, and made a pledge that the US government, for the first time, would guarantee the bonds issued by Fannie and Freddie.

住宅バブル崩壊で住宅ローンの保証を主な業務とするファニーメイなどが巨額の債務超過に陥っているのは明らかだった。一方で住宅公社など米政府機関が発行した長期証券の残高は当時の推計で1兆5000億ドル弱。暗黙の米政府保証がついた優良債券として、欧州やアジアの130を超える国の政府や中央銀行、機関投資家が保有していた。

It was clear that the collapse of the housing bubble left Fannie and Freddie deeply insolvent. In the meantime, the long-term bonds issued by them were estimated at that time to be about 1.5 trillion dollars. These bonds were considered high grade with implicit guarantee of the US government, and held by more than 130 entities such as governments, central banks, and institutional investors in Europe and Asia.

 懸念を特に強めたのは保有残高が1、2位の中国と日本。中国の胡錦濤国家主席は、外貨準備で保有する大量の米政府機関債を損失覚悟で売却処分する可能性をちらつかせ、外交圧力を強めた。

The two most worried countries were China and Japan, whose holdings were No.1 and No.2. President Hu Jintao of China pressured the US by threatening to sell its large holding of the bonds even at a loss.

 日本政府が中国の保有する米政府機関債を一部肩代わりする――。中国が米政府機関債を放出すれば、国際金融市場の動揺は計り知れない。幻に終わったが、一時はこんな構想が浮上。「日本は米国と真剣に内容を検討した」(国際金融筋)ほどの綱渡りが続いた。

At one time, a plan was being discussed whereby the Japanese government would take over (buy) part of the Chinese holding. If China dumped the bonds from Fannie and Freddie the damage to the international financial markets would be immeasurable. It didn't come to pass, but "Japan and the US were seriously considering the plan" (according to the source in international finance). The situation was very tense.

(Full article in Japanese at the link)


Slight quiver in his voice. That's poetic of Nikkei, but I think Mr. Bernanke's speaking voice always sounds like that.

By the way, how much Fannie and Freddie papers did China and Japan have at that time?

China had over 500 billion dollar worth of mortgage-backed securities from Fannie and Freddie, and Japan had over 250 billion dollars worth. The third largest holder was Russia, at slightly over 50 billion dollars.

From Nikkei (English labels are by me):


China and Japan were worried, Nikkei says. China threatened to dump, Japan was willing to buy what China would dump. In 20-20 hindsight, if China had dumped and Japan had picked up those MBS at a significant discount, maybe Japan would have no problem paying for the nuclear accident cleanup. Oh well.

Nikkei doesn't say why Federal Reserve was worried enough to start purchasing the MBS from Fannie and Freddie at that time. I don't remember the reason myself. All I remember was that the stocks of investment banks like Goldman Sachs, Citi, JP Morgan Chase were on a free fall in November, and a extra large downward pressure was on the stocks on November 21, 2008 which was Friday. After the announcement by Federal Reserve on November 25 next Tuesday, the stock markets were lifted somewhat, but all it did was to not fall for the duration of the year.